Sections include:
General Service Information
Warranty
Return of Defective Parts
Pressure
Care of Shoe
Care of &11 Padding
Oiling Instructions
Thermostats
Shocks
Correcting Oil Leaks
Vibration
Checking Heat Failures
&11 Drive Adjustments
How to Remove Clutch
Motor Repair or Exchange Policy
How to Handle Motor Exchanges
Westinghouse Motors
Emerson Motors
Delco Motors
General Electric Motors
Diagram - Gear Housing
Adjusting Gas Machines
Diagrams - Shoe Assemblies
Shoe and Element Parts
Wiring Diagram
Electrical Parts
Switch Parts
Roll Parts
Roll Small Parts
Drive Gears
Clutch Parts
Adjustable Knee Control Parts
Non-adjustable Knee Control Parts
Motor Mounting Parts
Frame and Base Parts
Cabinet Parts
Gas Machine Parts
Repair Parts

If you're Looking for the Owners Manual and instructions for the Ironrite please see this The Quick and Easy Way to Beautiful Ironing

WA-1050T, WA-1055T, WA-850T, WA855T, WA-852T, WA-857T, WA-750T, WA755T, WA-630T, WA635T, WA-600T, WA605T,

Beautiful images and full specifications included for each model.

WD-860T and WD-660T

Beautiful images and full specifications included for each model.

DA-1020T, DA-820T, DA-720T, DA-610T, DA-617T

Beautiful images and full specifications included for each model.

CE716 1961 Top of the line top/rear control panel model.
CE714 1961 Middle of the line top/rear control panel model.
CE712 1961 Bottom of the line top/rear control panel model.
CE710 1961 Front mounted control panel/free-standing model.
CE710U 1961 Front mounted control panel/under-counter model.
CE736 1963 Top of the line top/rear control panel model.
CE734 1963 Bottom of the line top/rear control panel model.
CE730 1963 Front mounted control panel/free-standing model.
CE730U 1963 Front mounted control panel/under-counter model.

How to light top burner pilots
Location of Safety Valves ( Natural or Mfg Gas) (LP Gas)
To light or relight oven pilot ( Natural Gas )
To light or relight oven pilot (LP Gas)
To light or relight high broiler (Natural or Mfg Gas and LP Gas)
How to use your top burners
How to use the Harper Center simmer burner
For ranges without Harper Center simmer burners
If top burner does not light
How to use griddle
How to use your oven
Your oven control
Operation of the O'Keefe & Merritt
Automatic Oven Signal Light
How to use your broiler
How to remove the grillevator for deep broiling
Use of the low broiler ( below oven )
Care of the broiler
Care of porcelain finish
Care of chrome plated surfaces
Care of griddle
Care of top burners and griddle burners
Care of the oven
Automatic Burner Control (ABC)
(How to use) ( How to set)
Instructions for installing and removing
HI-VUE glass and flue deflector
To remove HI-VUE glass
To replace HI-VUE glass
To clean reflector mirror
To clean chrome vent deflector
Instructions for removing and replacing
oven glass i n HI-VUE models
For easy cleaning under range
How to use the automatic oven timer
Your automatic oven timer
Buzzer timer
To use the timer for fully automatic operation
After the cooking operation is completed
To use the timer for semi-automatic operation
After the cooking ope ration is completed
Timed convenience outlet
For semi-automatic operation
Your automatic oven timer
Buzzer timer
To use the timer for fully automatic operation
After the cooking operation is completed
To use the timer for semi-automatic operation
After the cooking ope ration is completed
Tim ed convenience outlet
For semi -automatic operation
Electric signal timer
If you have a hand-wound timer
How to use your Temp 'N Time Control
How to level your range
Your oven light bulb
Baking Problems and Solutions
Cake difficulties
Pie difficulties
Cookie and biscuit problems
Bread baking problems
Miscellaneous

over a hot stove. Planning a meal is not hard and mixing
various ingredients into the promise of delicious dainties or
preparing a roast for the oven is rather fun . But to be held
in the kitchen or even in the house during the long hours of
watchfulness is a different matter. And it is right here that
the Westinghouse electric range steps in and lifts the burden.

When the food has been prepared it may be trusted to
this silent servant with perfect confidence. There is no possibility
of instructions being forgotten or misunderstood . At
a given time, (the time decided upon,) the clock will turn on
the current and the meal will begin to cook. Again when just
the correct temperature has been reached in the oven, the thermostat
will turn the current off again and when madam enters
the kitchen after an afternoon of leisure or pleasure the meal
is ready to serve.

She herself is prepared to enjoy the meal equally as well
as any member of the family , because she has not had to think
about it since early morning.

Because the Westinghouse range reduces the labors of cooking
to the minimum, requiring no watching nor constant regulation
of heat, because it produces better food , and because
it is more economical, it will be in the kitchen of every modern .
progressive woman who is anxious to keep her family happy
and in good health. and yet does not wish to become a fixture
in the kitchen with its consequent limitations.

SA-9-59, SS-9-59, S-9-59, D-11-59, D-13-59, FD-1 04-59, FI-123-59, FI-122-59, CP-144-59, FP-124-59 and FP-142-59.

"THE WONDERFUL 1959 FRIGIDAIRE REFRIGERATORS

Now with the advent of the wonderful new Frigidaire Frost-Proof Refrigerator-Freezer, a woman's life becomes easier than ever. For the first time she will have no frost to contend with. We hope you all have inspected a Frost-Proof that has been operating during the hot summer months and have seen how free of frost the packages and ice cube trays remain. You have only to see other refrigerators that depend upon push buttons for defrosting- to appreciate how much the absence of any frost means to the homemaker.

In the Frost-Proof:

• All of her frozen packages stay clean and free of frost.
• Labels on the frozen food packages are always clear and legible.
• All space is usable- none taken up by the frost.
• Freezer baskets always roll in and out easily-no tugging to release frosted guides.
• Ice cubes remain free of frost whether in ice trays or in the Ice Server.
• Ice Cream stays free of frost on the surface of the un-used portion- yes, even if Junior leaves the lid ajar.
• Counter-tops and tables stay dry and clean of frost marks or puddles of melted ice formerly left from grids or ice trays or frosty packages.

But the advantage the homemaker appreciates most is the freedom from the messy job of defrosting! Remember that some of the women you talk to may never have experienced the messy job of defrosting a true food freezer-refrigerator. But every woman will have at least some experience with some kind of defrosting."

Built-in ranges and cooktops:
RF17 RF19 RF28 RFX37 RF38 RF48 RU15 RUX37 RU38 RU47 RU48 RU76

Built-in Ovens:
RJ16 RJ38 RJ66 RJ84 RJBB RL36 RL76

30" Ranges:
RB305 RB315 RB320 RB335 RB345 RB355 RB366 RB375

40" Ranges:
RC420 RC435 RC445 RC455 RC456 RC459 RC479

Major sections include:
FEATURE CHARTS
GENERAL INFORMATION
INSTALLATION
SERVICING
SWITCHES
INFINITE HEAT CONTROLS
THERMOSTATS
ELECTRIC SUPERMATIC UNIT CONTROL
AUTOMATIC ROAST
TIMERS
APPLIANCE RECEPTACLES AND CIRCUIT BREAKERS
COOKING TOPS
CALROD®SURFACE AND OVEN UNITS
RANGE BODIES
STORAGE COMPARTMENT AND DRAWER
OVEN DOORS AND HINGING
OVEN LINERS
ROTA-GRILL MOTORS
RANGE SERVICE CHART

Models include:
1960: KAA40, KCA40, KDA40, KEA40, KFA40, KBA30 KAA30, KCA30 KDA30 KEA30 KFA30

1961: KAB40, KBB40, KCB40, KDB40, KEB40, KFB40, KAB30, KBB30, KCB30, KDB30, KEB30, KFB30

1962: KAC40, KBC40, KCC40, KDC40, KEC40, KFC40, KAC30, KCC30, KDC30, KEC30, KFC30

"No matter how much you've enjoyed cooking in the past, there's even
greater pleasure awaiting you now that you have a new Westinghouse
'Speed Electric Range. It's easier to use and gives you better results than
any range you ever used. And it's easy to clean, too.

No longer need you stand at your range and stir foods as they cook. Nor
will you ever need to worry about baking-you'll get perfect results every
time in your Westinghouse Oven.

There's new accuracy in surface cooking, too. There are marked heats
on the control of each surface unit. But you can "fine-tune" any heat you
want between those settings, so that your favorite dishes come out exactly
as you want them.

This book tells you how to use your Westinghouse Range to get perfect
results. So, please read these instructions carefully, and follow them
faithfully."

Commander AC-774, AC-74, BC-74
Champion DC-74
Commodore ECA-74
Challenger EC-74

Now cooking will really be fun at your house!
Your new Westinghouse Speed-Electric Range will make cooking
so much pleasanter and easier. Foods will taste better, look better and
be better for you... and you'll have a cleaner, cooler kitchen, too.

Your new range has timesavers, moneysavers and flavorsavers.
Read the "How to Use" section for your particular model and learn
to use each feature for all it's worth!

Of course, you can still use all your favorite recipes . . . with greater
convenience and sureness than ever before. There are lots of new
things you can do, however, with accurately controlled electric heat.
Don't overlook the important cooking tips in the Recipe Section...
they are given special emphasis in the Index on page 80.

Very cool article on Maytag's new all-pushbutton Automatic Washer.

How Westinghouse's Roast Guard feature works on their electric ranges.

New packaging design for GE Appliances.

• Anti-freeze


• Floor waxes (brands tested: Aerowax, Beacon, Beautiflor, Butcher, Continental, Ful-Gleam, Fullustre, Johnson's Glo-Coat, Johnson's Paste, Kengrip, Klear, Preen, Sears Maid of Honor, Simoniz, Stanley, Stride, Wilbert)


• Should you wax your floors?


• Pop-up toasters (brands tested: Fostoria, General Electric, Hamilton Beach, Nelson, Toastmaster, Westinghouse)


• Painting of galvanized steel


• Painkillers and "cold remedies"


• Patent medicines bought over the druggist’s counter without prescription may often be dangerous


• Home is where the hazard is...
  You can’t be too careful around moving machinery— many household appliances have their perils. One unsafe condition or one unsafe act may be the cause of an accident. If both occur, as may happen, you, or a child in the home, are likely to be in real trouble


• Low-priced stereo amplifier


• Three stereo pickup cartridges (brands tested: General Electric, Shure Custom, Shure Professional).


• Removing tree stumps


• Paint at a bargain?


• "National Titanium" is with us again


• Misleading labels on electric appliances


• Single-solution processing of photographic film


• First, send for the fire department—unskilled attempts to put out fires are often futile, may be fatal


• Clippings on matters of consumer interest are welcome


• Eliminating bats

Regular Features Include:

• The Consumers’ Observation Post


• Brief cumulative index


• Editorial What is a good television program, and who says so?


• Listings of Current Phonograph Records


• Ratings of Current Motion Pictures

If you are looking for the gas Maytag wringer washer service manual please see this manual...

Maytag Gas and Electric Washer Service Manual

J299S, J301S, J302S, J303S, J305S, J308S, J400S, J401S, J403S, J405S, J408S, J411S.

If you're looking for the service manual to these ranges please see this document:

1959 GE Electric Range Service Manual

The Deluxe Air-Flow cleaner, model AVT-173

A brilliant new tank cleaner, model AVT-811

A. How to correctly uncrate the Automatic Washer.

B. How to correctly install the machine.

C. How to correctly instruct the customer of its use.

D. How to correctly dismantle and reassemble machine.

E. How to diagnose and correct service reports which they might encounter.

Throughout this manual we will not refer to your individual models but will cover all variations by referring to factory model numbers which are contained in the serial number found on the serial plate of each machine. Example: XAIB-YZOOO. The letters AIB or second, third, and fourth letters and digits will indicate the factory model numbers.

Please note this original copy was marked with notes and underlines of the text. These are extensive and could not be removed. However, the text and images are completely clear and readable.

Editorial: The Fourth of July

New Switchgear Laboratory Goes into Operation
Late last month on the flatlands of southwest Philadelphia, GE’s new high-capacity switchgear development laboratory was officially dedicated. With Company spokesmen looking ahead to an annual U.S. power consumption of possibly a trillion kw-hrs by 1965—more than triple the amount now being used—the new laboratory will aid in the development of switch- gear of higher ratings to keep pace with this phenomenal growth. continued…

Engineering the Automatic Washer
The automatic clothes washer is a simple device—to the housewife. She throws in the laundry, sets a control dial, and goes about her telephoning. A short time later she removes the laundry—washed and damp-dried.

Simply stated, the function of a domestic washing machine is to get the laundry clean, rinse out the detergent, and extract most of the water. For a third of the century these operations were performed with a machine in which the laundry was manually lifted from the tub and fed through a water- extraction device. Most of these devices were wringers, powered by the washing- machine motor. A limited number were the centrifugal-extraction type using the same or a separate tub. continued…

Stopping Ships
Even with modern navigating and communication aids there are times when things get out of hand and a collision ol ships appears imminent. The need for meeting this situation—rare though it may he—has an influence on the design of ships’ power plants.

Most large and fast ships are powered bv a steam turbine that drives the propeller through suitable gearing and shafting. The astern power that is used for stopping a ship is provided by a comparatively small separate section of the main turbine. The question immediately arises as to why the astern element can’t be given the same power as the ahead element. Well, it can. The simplest arrangement would he another turbine of the same size geared to drive the propeller backwards. continued…

Ferromagnetography
Contrary to general belief printing did not originate with Gutenberg; to the ancient Chinese belongs the credit. They made engravings—used mainly for printing on silk cloth—by carving figures out of wooden blocks. Later, around 1120 BC. they introduced wooden blocks of movable type.

Modern printing, on the other hand, began in the middle ages—about the year 1423. It was during this period that Johann Gutenberg, a German stonemason, had the idea of printing with movable type. So he set about his skill, cutting alphabets out of small wooden blocks to be used for typesetting. A friend advised him to use metal instead of wood, since it wouldn’t wear out so easily. This he did. As you can imagine, this task required many years and a large expenditure of money. He financed his operations by borrowing money on the type he’d already completed. Then, to prove to his creditors and the many cynics the worth of his efforts, he completely reproduced the Bible in print. continued…

Cool Breezes — Story of the Electric Fan
Fans preceded written history by many centuries. Some of the most ancient known fans were those of the Chinese dating back to 3000 BC. And ceremonial fans were used in 1700 BC by the reigning monarchs of Egypt and Assyria. Some thousand years later the "punkah" —a hand-swung lightweight ceiling-suspended fan—was introduced in India, and even today is still in use there.

From exquisitely made folding tans of the Japanese, followed by 17th century Paris creations of surpassing beauty, we come to the practical palm-leaf type and simpler folding fans of grandmother’s day.

It’s not possible to give the exact age of the electric fan—the youngest member of the ancient family of fans. But the earliest record of a U.S. patent awarded for an electric fan was in 1854. This was a ceiling-suspended assembly of several large fan blades, each hinged along one edge to a horizontal rotating arm driven by a battery-operated motor. Arms on the blades struck projections causing the blades to vibrate and thus agitate the air. continued…

Longer Life for Dry-type Transformers
Improvements in dry-type power transformers and their insulations is a good example of how electrical engineers are continually making progress in lengthening the life span of electric equipment and increasing its endurance to higher temperatures.

For many years insulations known as Class A were about the only ones available to the transformer designer. These insulations consisted of materials such as cotton, silk, or paper—impregnated with organic varnishes to give them additional mechanical and electrical strength. They were used in a medium of mineral oil or air. Such insulations were relatively inexpensive but a maximum allowable temperature limit of 105 C was necessary for reasonable life. continued…

The G10 Germanium Rectifier
In 1886 a German chemist by the name of Alexander Winkler found an unknown metal sulfide and isolated the element which he called germanium. It has a shiny metallic appearance, is extremely hard and brittle, and is recovered as a by-product in the smelting and refining of zinc ores.

Because germanium falls into group four of the periodic table, it has some of the chemical characteristics of the elements on either side of it. Germanium is both an electrical conductor and an electrical insulator, depending on its temperature, and is classed as a semiconductor. continued…

Nylon for Bearings and Gears
Although nylon is generally associated with such decorative items as stockings and sweaters, we have found that its versatility extends well into the fields of bearings, gears, and other workaday applications.
Nylon is tough at low7 temperatures, is resistant to abrasion, has strength in thin sections, is light in weight, has certain self-lubricating qualities, and is resistant to many chemicals. Properties are given in the table on the opposite page. Exact characteristics and specifications can be found in the literature put out by the manufacturers of nylon molding powders.

Bearing Tests - Of interest to design engineers is published data that shows the effect of wear on nylon when used as a bearing material. Results of tests using nylon against nylon, steel, and brass under various loads and speeds, and with various lubricants, are given on page 35. As you may suspect, the lowest rates of wear are found when nylon is run against nylon in a dry condition, as well as when nylon is run against steel lubricated with SAE 10 oil. When nylon is rubbed against brass, the metal flakes off and contaminates the hearing surface. continued…

The Unit Cost of Light
There’s more to figuring the cost of a lighting system than adding up the prices of fixtures, installation, and electricity. A tabulation of over-all annual costs that the customer may expect to pay appeals to the businessman, because it is expressed in his own language. Rut further analytical cost studies of operating and maintenance methods and lamp efficiencies may show you the way to worth-while savings or better lighting for the same expenditure.

To help you along this economic pathway a relatively simple formula has been devised. It is referred to as the "unit cost of light” method. In its most flexible form it deals with the raw light as generated by the lamps in just one fixture. Then, once the unit cost of light in dollars per million lumen hours is known, you can easily apply it to a specific installation if over-all costs are also desired. continued…

Added Kick for Turbojet Engines
Getting an 80-ton airplane into the air in a matter of seconds is no easy job. The problem is one of providing more than normal maximum thrust or "kick” at take-off. In the case of B-45 and B-47 jet bombers, their power plants (J-47 turbojet engines—one is shown on the adjacent page) were equipped with combustion-chamber water-alcohol injection systems for augmenting thrust.

Variations of these systems boost the take-off thrust from 15 to 25 percent or higher. As a result, heavy jet-powered aircraft can take off from minimum- length runways with maximum safety. continued…

Are We Ready for Railroad Electrification in the U. S.? .
Admittedly, widespread electrification in I lie United States is not just around the corner. Rut there is an element in the cost of railroad electrification and in the success of operation through the ensuing years that can not be settled too soon. This all-important factor is standardization. And standardization is so important primarily because it permits repetitive manufacture. Standardization, of course, offers other advantages that may be more familiar, but every day brings new evidence that a custom-designed article built in a job shop cannot compete with a highly engineered item produced under conditions of repetitive manufacture.

It is time for all who may have a hand in railroad electrification in the United States to start sifting out the alternatives and to find agreement on what may be the standard system of electrification in this country. Let us speak briefly about the prospects of electrification and [hen expand the theme of standardization. continued…

A Brightening Outlook - When will we see railroad electrification resumed in the United States? The answer depends largely on costs, with the cost of fuel or energy being a big part of the expense of locomotive operation.

When we compare the cost of diesel fuel with the cost of purchased electric power at the figures current today, we find them roughly equivalent. We are speaking, of course, of gallons of fuel oil or kilowatt-hours of electricity at the locomotive. As long as power costs in these two forms are even approximately equal, it is obvious that the diesel- electric locomotive with its lower investment is the correct answer for new installations. At the same time this approximate equality tells us that extensive electrified systems already installed should continue to be operated. continued…

New Safeguard for Protective Coatings
You can best define a plastics material as a synthetic organic substance. At some stage of production it’s plastic— capable of being shaped; or liquid— capable of being cast. Furthermore, it’s either thermoplastic or thermosetting. If thermoplastic, it softens under heat and can he remolded. If thermosetting, it sets under heat and can’t be remolded.

Phenolic materials are thermosetting plastics. And from practically the outset of the industry they’ve enjoyed an ever- expanding market. They take many and various forms. Probably the most familiar to you are radio cabinets, telephone handsets, buttons, tube bases, mechanical parts, and so on. continued…

Dollar-sign Engineering
The photo sequence beginning on the next page will show you how a value analyst operates—step by step—on a typical project. Here, it’s the timer for the automatic clothes washer. Because space doesn't permit us to show the results of the analysis on every part of the timer, we have selected one part as being typical. (In the actual project more than 30 individual parts of the timer were analyzed for value.)

It should be emphasized that nothing was wrong with the timer when we approached the Value Analysis Unit and requested a survey. The timer operated satisfactorily and costs were in line with similar products. But. as is the case with far-sighted management, they wanted to see if it wasn’t possible to further eliminate any unnecessary costs. continued…

Moisture vs Rubber Insulation
Although rubber compounds are used to waterproof such everyday items as overshoes, raincoats, and garden hoses, rubber compounds in general can’t be considered waterproof when used as an insulation for wire and cable.

What works on raincoats may not work on cables—the basic differences are: length of exposure; effect of moisture on the electrical properties. Cables insulated with rubber compounds must withstand years of continual exposure with a consequent absorption of moisture. And moisture absorption has proved to be a contributing factor in cable failures. continued…

KDB-21B
KDA-21
KDI-61
KDI-21B
KDI-210
KDC-210